Model HP-II: High Pressure Blower

Cincinnati Fan manufactures the Model HP-II High Pressure Blowers in 12 models, each available with multiple wheel sizes. The Model HP-II include continuously welded heavy gauge steel housings with removable inlet plates and housings, Teflon shaft seals, and flanged inlets and outlets.

Two different wheel designs are available, including one with a continuously rising pressure characteristic for assured stable operation to complete shut off. The Model HP-II is also available in all aluminum or all stainless steel construction.

This blower is available in AMCA A, B, or C spark resistant construction.

PERFORMANCE RANGE:

• Capacities up to 7,000 CFM and 78″ SPWG
• Standard construction, airstream temperatures up to 200°F (93°C)
• Optional high-temperature construction, temperatures up to 750°F (398°C)

FOR HIGHER CAPACITIES:

Pressure: See Model RBE

FIND A REP

  • FEATURES & BENEFITS
  • ARRANGEMENTS
  • OPTIONS
  • APPLICATIONS
  • RESOURCES

Features

  • Each radial blower model is available with four to six wheel sizes for more airflow selections with a direct drive arrangement.
  • Continuous welded housings and teflon shaft seal to prevent air leakage.
  • Inlet and discharge flanges drilled per ASA, 150-pound and ANSI, 125-pound standard pipe sizes, are standard.
  • Blower housings are reversible and rotatable in 45° increments.
  • Removable inlet & drive side plates allow wheel or motor, or shaft & bearings on belt driven models, to be removed without disconnecting inlet or discharge connections.
  • All fans receive a mechanical run test to ensure proper balance and alignment before shipping.
  • Arrangement 8 units come standard with shaft/coupling guards.
  • Arrangement 9 and 9CB units come standard with belt guards.
  • Also available in aluminum or stainless steel construction.

Benefits

  • Multiple Wheel Selections: With each model being available with four to six different wheel sizes, you are almost assured that a direct drive model will be available for your performance selection. Decreases the need for larger, more expensive belt driven models.
  • Rugged Construction: Housings are 7 and 10-gauge steel and are continuously welded to prevent leakage. Fan bases are 7 and 10-gauge steel to prevent pulsation at all conditions. Less field problems.
  • Standard Features: All units include a teflon shaft seal to minimize leakage and discharge flanges drilled to ASA, 150-pound, and ANSI, 125-pound standard pipe sizes. No additional cost.
  • Rotatable Housings: All models have housings that can be reversed and/or rotated in 45° increments in the field. Allows for field conversion without replacing the blower.
  • Ease of Maintenance: Replacing a wheel, motor, or shaft and bearings on belt driven models, is easily accomplished without disturbing the inlet or discharge pipe connections. It minimizes extended downtime.
  • Quality Components: All belt driven models have self-aligning, cast iron, re-lubricatable, pillow block bearings sized for a minimum 150,000 hours average life. All fan shafts are turned, ground, and polished and are coated with a high quality rust preventative before shipment. Long dependable service.
Arrangement 1 - Belt Drive
Arrangement 1 – Belt Drive
Arrangement 4& 4HM - Direct Drive
Arrangement 4& 4HM – Direct Drive
Arrangement 8 - Direct Drive
Arrangement 8 – Direct Drive
Arrangement 9 - Belt Drive
Arrangement 9 – Belt Drive
(Shown with shaft guard option)
Arrangement 9 - Belt Drive
Arrangement 9 – Belt Drive
(Shown with belt guard removed)
Drain Connection
Drain Connection
Inspection Door
Inspection Door
Inlet Bell
Inlet Bell
OSHA Type Outlet Guard
OSHA Type Outlet Guard
Shaft and/or Heat Slinger Guard
Shaft and/or Heat Slinger Guard
  • Combustion air
  • Blow-off
  • System pressurization
  • Pneumatic conveying
  • Material conveying

FIND YOUR LOCAL SALES REP

Exceptional local support with over 170 experienced sales engineers in 56 offices strategically located across the U.S. and Canada to assist you.

START HERE